100% Employee Owned, Founded 1954

Jordan Valve Technical Guide: Installation of a PRV

Provider Resource

Jordan Valve Technical Guide: Installation of a PRV 1

Ideal Installation of a PRV in a Steam System

The following technical guide from Jordan valve show the ideal installation of a pressure relief valve in a steam system.

  1. To protect the valve from grit, scale, thread chips and other foreign matter, ALL pipelines and piping components should be blown out and thoroughly cleaned before the installation process begins.
  2. Shutoff valves, pressure gauges and by-pass piping should be installed as indicated in the Ideal Installation Schematic to provide easier adjustment, operation, and testing.
  3. A line strainer should be installed on the inlet side of the valve to protect it from grit, scale and other foreign matter. A 0.033 perforated screen is usually suitable for this purpose. Line strainers are available from Jordan Valve.
  4. For best control, 3’ 0” straight sections of pipe should be installed on either side of the valve.
  5. In preparing threaded pipe connections, care should be exercised to prevent pipe-sealing compound from getting into the pipelines. Pipe-sealing compound should be used sparingly, leaving the two end threads clean. Jordan uses, and recommends, thread sealer Teflon ribbon.
Jordan Valve Technical Guide: Installation of a PRV 2
  1. The flow arrow on the valve body must be pointed in the direction of flow. Ideally, the valve should be installed in the highest horizontal line of piping to provide drainage for inlet and outlet piping, to prevent water hammer, and to obtain faster response.
  2. If possible, install a relief valve downstream from the valve. Set at 15 psi above the control point of the valve.
  3. In hot vapor lines, upstream and downstream piping near the valve should be insulated to minimize condensation.
    In gas service, if the control pressure (downstream)is 25% of the inlet pressure or less, expand the outlet piping at least one pipe size. A standard tapered expander connected to the outlet of the valve is recommended.
  4. Where surges are severe, a piping accumulator is recommended.
    On steam control applications, install a steam trap with sufficient capacity to drain the coil or condenser. Be sure to have a good fall to the trap, and no back pressure. Best control is maintained if the coil or condenser is kept dry.

For more information, or see ideal installation steps for the Control Line, (required in externally-sensed pressure regulating valves) contact a process solutions expert from Cross Company.

As a distributor for Jordan Valve throughout our territories in the U.S. Mid-Atlantic region, Cross company offers a range of products along with expertise to ensure your operating is running efficiently. Contact us today for a quote or to learn more about our full offering from Jordan Valve.

See how our team can help improve quality, increase efficiency, and reduce risk

Related Posts

Parker Logo
Parker Resource Quick connections for high-pressure, hydraulic applications have evolved significantly in response to new processes and operational needs. As industries advance their capabilities,
November 21, 2022
Parker Logo
Parker’s Transair Products Offer Faster Installation and Corrosion and Contamination Resistance for Technical Rooms Technical rooms generally feature reduced space, aggressive environments and pressure
October 28, 2022
Parker Logo
Offering Outstanding Reliability and Cost Efficiency Our North Carolina ParkerStore locations offer the exclusive Colorflow line of valves. These valves feature a reference point
October 26, 2022

Hang Tight! We're Searching... Searching... Searching...

We’re looking through thousands of pages to find the most relevant information.

In the meantime, enjoy these fun facts…

Did you know... the precision measurement group at Cross was founded in 1939 by our current CEO's grandfather, Jim King. That's a whole lot of calibration!
Did you know... A fingerprint weighs about 50 micrograms. We know, we weighed it! The residue left from a finger can actually make a difference in weight results which is why we wear gloves when we calibrate weights. For reference, a sheet to paper is about 4.5 grams, that’s 4.5 million micrograms.
Did you know… Cross Company is an ESOP (Employee Stock Ownership Plan). Our ESOP started in 1979 and as of 2006, we are a 100% employee owned! Learn more about our ESOP and how that benefits both team members and our customers.
Did you know… Cross Company has grown significantly since our start in 1954. Over the years we've acquired 26 companies! Today, our five groups have expertise in everything from industrial automation to precision measurement, and industry knowledge going all the way back to 1939.